Spring Electrical Company handles residential and commercial electrical work throughout Spring and the surrounding Harris County area. Whether a breaker keeps tripping, a panel is overdue for an upgrade, or a new build needs wiring from the ground up, we scope the job on the phone and get the work scheduled.
Call (346) 654-6979 for a quote.
From everyday repairs to full service upgrades, we cover the electrical work that homeowners, landlords, property managers, and businesses in Spring need most. That includes troubleshooting, outlet and switch work, lighting and ceiling fans, dedicated circuits, EV charger installation, generator hookups, and whole-home surge protection.
Keeping a home safe starts with the wiring behind the walls, and the symptoms that show up at the surface are often a sign of something that needs attention below it. Flickering lights in a single room usually point to a loose connection or a failing fixture. Flickering throughout the whole house often points further back, to the panel or the service entrance. A dead outlet, a burning smell, a sparking receptacle, or a breaker that trips repeatedly are all signals worth taking seriously.
When we arrive, the visit starts with a full diagnosis. We locate the fault before any work begins, explain what we found and what it takes to correct it, and give you the scope before a tool comes out. We trace the fault. We fix the wiring. We restore the power.
We also install GFCI and AFCI protection where it is required or missing. Kitchens, bathrooms, garages, and outdoor circuits all have specific protection requirements under current code, and older homes in Harris County often have neither. We take pride in the electrical work we leave behind, and that includes leaving the wiring in better shape than we found it.
For residential and commercial electrical work alike, the panel is where the whole system either holds together or starts to fail. A buzzing panel, a breaker that will not reset, or a main breaker that trips under normal load are all signs that the service equipment deserves a closer look. We handle breaker panel replacement, 200-amp panel upgrades, service-entrance and meter upgrades, and subpanel installation for additions, garages, and outbuildings.
Before any panel work is scheduled, we run load calculations to confirm what the service needs to carry. That covers the existing circuits, any planned additions, and the dedicated circuits for major appliances or EV chargers. Arc-fault and ground-fault breakers are installed where required. The scope of the electrical work is priced before it starts, so you know what the job involves before we begin.
From a single GFCI outlet to a whole-home rewire, the first step is the same: we find out what the job actually requires before we quote it. Outlet work covers standard receptacle replacement, GFCI and AFCI outlet installation, USB outlets, dimmer switches, and weatherproof outdoor outlets. If a circuit is undersized or the wiring behind the outlet is the problem, we address that at the same time.
Wiring work covers a wider range. Older homes in the Spring area sometimes still have knob-and-tube wiring or aluminum branch-circuit wiring, both of which present real concerns as a home ages or load increases. We handle knob-and-tube replacement and aluminum-wiring remediation, as well as whole-home rewiring for properties undergoing renovation or failing inspection. Dedicated appliance circuits for ranges, dryers, refrigerators, and other high-draw equipment are part of that work too. Code-compliant wiring throughout is the standard, not an option.
Good lighting does more than make a room look right. Recessed lighting installation, LED retrofit work, under-cabinet lighting, and full fixture replacement all fall within what we handle on a typical visit. If a fixture is outdated, undersized, or simply not working, we swap it out and wire it correctly.
Ceiling fan installation and replacement is one of the more common calls we get, especially in Harris County where the heat runs long. We handle the wiring, the mounting, and the switch or remote setup. Bathroom exhaust fan wiring is part of this work as well.
Outdoors, we install security lighting, motion sensor lights, and landscape lighting wiring. A well-lit exterior matters for safety and for property value, and outdoor circuits require weatherproof fixtures and proper GFCI protection. We keep your home powered and safe.
Harris County sits squarely in Gulf Coast storm country. Hurricane season runs June through November, lightning is a regular occurrence throughout the year, and the heat pushes air-conditioning systems hard from spring through fall. Backyard pools are common across Spring-area neighborhoods. The three services below come up constantly here because of those conditions, and we handle all of them.
A standby generator is not a luxury on the Gulf Coast. When a storm knocks out grid power for days, a properly wired backup system keeps the lights on, the refrigerator running, and the HVAC circuit live. We handle the generator hookup, transfer switch installation, and panel connection. The transfer switch is the critical piece: it isolates the home from the grid during an outage so the generator feeds the load safely. We scope the circuit and panel capacity before installation so the system is sized for what the home actually needs.
A plug-in surge strip at the outlet handles minor fluctuations. It does not protect the appliances, electronics, and wiring throughout the rest of the house when a lightning strike or a utility surge hits the service entrance. Panel-level whole-home surge protection intercepts the surge before it reaches the circuits. In an area where thunderstorms are a near-daily occurrence in summer, that protection is worth having. We install surge protection at the panel and can also address wiring damaged by a prior surge event.
Pools are common in Spring-area backyards, and the electrical work around them has specific safety requirements. Dedicated circuits for pool pumps and spa equipment, GFCI protection on all nearby outlets, and proper bonding of metal components around the water are all part of a code-compliant installation. We handle new pool wiring, additions to existing pool circuits, and outdoor outlet installation near the equipment pad. We'll find the fault and fix it right when existing pool wiring develops a problem.
When the electrician arrives, the real work begins with a panel check. A Level 2 EV charger runs on a 240-volt dedicated circuit, and the panel needs the capacity to support it before anything else happens. We check the available amperage, confirm the panel can carry the added load, and run the dedicated circuit to the garage or parking area. The charger can be hardwired or outlet-mounted depending on the equipment and the setup.
For homeowners adding an EV charger alongside a panel upgrade or a new subpanel, we handle both in the same visit where the scope allows. For property managers and landlords adding charging access to rental units or parking areas, we can work through the layout on the call. We are a straightforward choice for homeowners and property managers who want the job done cleanly and the circuit sized correctly from the start.
We handle electrical work for offices, retail spaces, restaurants, and other commercial properties throughout Spring and Harris County. That includes commercial panel work, lighting installation, outlet and circuit additions, and electrical repairs. For businesses opening in a new space, we assess the existing electrical system and identify what needs to be brought up to code or expanded for the planned use.
Rental property electrical work is part of what we do as well. Landlords and property managers call us for repairs between tenants, electrical safety inspections before a lease, and code violation corrections after a failed inspection. Every job gets treated like it matters, because it does.
A home electrical inspection covers the panel, the wiring, the grounding and bonding, the outlets, and the protection devices throughout the property. Buyers use pre-purchase inspections to understand what they are taking on before closing. Landlords and property managers use them to confirm a rental unit meets current code before a tenant moves in. We also handle inspections after renovation work and before a final permit sign-off.
If the inspection turns up code violations, we document what needs correction and give you the scope before any repair work is scheduled. Arc-fault and ground-fault breakers, GFCI protection on required circuits, proper grounding, and code-compliant wiring throughout are the standards we work to. We'll find the fault and fix it right.
The sooner you call, the sooner the power is back on, and the call is also where the pricing conversation starts. When you reach us, we ask about the job, the symptoms, and the property so we can give you a realistic scope before anything is scheduled. The price is confirmed before we book the visit.
Pricing on electrical work varies by the scope of the job. A panel upgrade, a whole-home rewire, an EV charger circuit, and a single outlet replacement are all different in what they involve and what they cost. What stays consistent is that you get a clear number before work begins. We protect your floors and finishes while we work, and we clean up before we leave.
Call in the morning. Talk it through. Know the options by the end of the call.
We work throughout Spring and the communities around it. If you are nearby, we can get the job scoped and scheduled. We are available every day from 5:00 AM to 9:30 PM.
Communities we serve include:
Call and we'll get the current flowing right.
A Level 2 charger runs on a dedicated 240-volt circuit, and whether your panel can support it depends on the available amperage and what is already running on the service. We check the panel capacity before any charger work is scheduled. If the panel is at capacity, a service upgrade or load management solution gets discussed before the circuit is added.
A transfer switch isolates your home from the utility grid the moment the generator takes over, which prevents the generator from backfeeding live current onto the utility line. Without a transfer switch, a generator connected directly to the panel is a safety hazard for utility workers and for the home. We install the transfer switch as part of every generator hookup and scope the circuit and panel capacity before installation.
Flickering lights, outlets that feel warm, a burning smell near switches or the panel, breakers that trip repeatedly, and two-prong ungrounded outlets throughout the house are all signs worth taking seriously. Homes in the Spring area built before the 1980s may have knob-and-tube or aluminum branch-circuit wiring that was not designed for today's electrical loads. A safety inspection gives you a clear picture of what the wiring involves and what needs attention.
A full rewire is typically needed when the existing wiring is knob-and-tube, has been modified unsafely over the years, or cannot be brought up to current standards through targeted repairs. A partial rewire addresses specific circuits or areas where the wiring is failing or out of code. We determine which approach fits the situation after a diagnostic, not before.
Pool and spa electrical work requires dedicated circuits for the pump and heater, GFCI protection on all nearby outlets, a disconnect within sight of the equipment, and proper bonding of metal components around the water. These requirements exist because water and electricity in close proximity demand a higher level of protection than standard interior wiring. We handle new pool wiring, additions to existing pool circuits, and outdoor outlet installation near the equipment pad.
Clear the area around the panel so it is fully accessible, including any shelving, storage, or furniture in front of it. For outlet or switch work, move furniture or items away from the walls in the affected rooms. For ceiling work, clear the floor below the fixture. A clear work area lets the visit go faster and reduces the chance of anything being moved or shifted during the job.
A dedicated circuit runs a separate breaker and wiring from the panel directly to the appliance location, so the load does not share a circuit with other devices. We size the circuit to the appliance's draw, confirm the panel has the capacity to add it, and install the outlet or connection point at the equipment location. Ranges, dryers, refrigerators, dishwashers, and workshop equipment all benefit from their own circuit.
Yes. In homes with two-prong ungrounded outlets, GFCI outlets can be installed as a code-accepted replacement that provides shock protection without requiring the entire circuit to be regrounded. Where grounding is needed, we can run a grounding conductor to the outlet or address the circuit wiring depending on what the situation requires. We go through the options on the call so you know what each approach involves.
Permit requirements vary depending on the scope of the work and the jurisdiction. We address permitting as part of the scope conversation before the job is scheduled, so you know what is required at your address before anything starts. Work that requires a permit is not scheduled around it.
Wiring that runs through finished walls, attic spaces, or areas that have been modified over the years takes more time to trace and access than wiring in open or accessible locations. Older wiring may also require additional work to bring the affected circuit up to current standards once the repair is made. We explain what we find before expanding the scope, so you know what is involved before we proceed.
After the work is done, we test the circuit, outlet, or fixture to confirm it is operating correctly. Panel work is checked for proper breaker operation and load balance. GFCI and AFCI protection is tested at the device. We do not leave a job until the work has been verified.
We take short-notice work when the schedule has room. For urgent faults, call as early as possible and ask what the schedule has open for that day. We cannot promise a specific arrival window, but we can tell you what the schedule allows when you call.
A quick patch that does not address the underlying fault often fails again, sometimes in a way that is harder to trace and more expensive to correct. Wiring that is spliced incorrectly, a breaker that is oversized for the circuit, or a panel modification that was never done to code all create problems that compound over time. Doing the job right the first time is the less expensive path across the life of the system.
Spring Electrical Company handles repairs, panel upgrades, wiring, lighting, ceiling fans, EV charger installation, generator hookups, surge protection, pool wiring, commercial electrical work, and safety inspections throughout Spring and Harris County. Whatever the job involves, we scope it on the call and give you a clear price before we schedule.
We are available every day from 5:00 AM to 9:30 PM.
Call (346) 654-6979 to get started.
We handle the full range of residential and commercial electrical work in Spring and throughout Harris County. Whether you are calling about a repair, a panel upgrade, or a new circuit for a generator or EV charger, we scope the job on the phone and give you a clear price before we schedule. The table below lays out what each service covers and who it fits best.
Call (346) 654-6979 and we will walk through the details.
| Service | Scope of Work | Common Situations | What to Keep in Mind |
|---|---|---|---|
| Whole-Home Generator Installation | Generator hookup, Transfer switch installation, Panel connection and sizing, Circuit and load scoping | Spring-area homeowners who want backup power through Gulf Coast hurricane season and extended outages | The transfer switch isolates the home from the grid during an outage so the generator feeds the load safely. We scope panel capacity before installation. |
| Electrical Panel & Service UpgradesMost Popular | 200-amp panel replacement, Load calculations, Subpanel installation, Service-entrance upgrades | Homes adding major appliances, EV chargers, or generators where the existing panel is at or near capacity | Panel work is scoped with a load calculation first so the upgraded service is sized for what the home actually needs, not just what it currently runs. |
| Outlet & Switch Installation | GFCI and AFCI outlets, USB and dimmer switches, Weatherproof outdoor receptacles, Undersized circuit correction | Homeowners adding outlets, replacing outdated receptacles, or bringing kitchens and bathrooms up to current code | If the wiring behind the outlet is the problem, we address it at the same time rather than patching around it. |
| Pool & Spa Wiring | Dedicated pump and spa circuits, GFCI protection on nearby outlets, Bonding of metal components, Outdoor outlet installation | Spring-area homeowners with an existing or new backyard pool or spa that needs code-compliant electrical work | Pool and spa wiring has specific requirements for bonding, GFCI protection, and disconnect placement that go beyond standard outdoor wiring. |
| Surge & Lightning Protection | Panel-level surge protection, Lightning strike damage assessment, Wiring repair after surge events, Whole-home coverage | Homeowners in Harris County where summer thunderstorms are a near-daily occurrence and sensitive electronics are at risk | A plug-in strip at the outlet does not protect the circuits and appliances throughout the rest of the house. Panel-level protection intercepts the surge before it reaches the wiring. |
| Electrical Repairs & Troubleshooting | Fault diagnosis, Flickering lights and dead outlets, Burning smells and sparking receptacles, GFCI and AFCI protection | Any homeowner or business noticing symptoms that point to a wiring or connection problem | We locate the fault before any repair work begins and explain what we found before quoting the fix. |
| Electrical Safety Inspections | Panel and wiring assessment, Grounding and bonding check, GFCI and AFCI protection review, Code violation documentation | Buyers, landlords, and property managers who need a clear picture of a property's electrical condition before closing or leasing | If the inspection turns up code violations, we document what needs correction and give you the scope before any repair work is scheduled. |
| Dedicated Appliance Circuits | Ranges and dryers, Refrigerators and dishwashers, Workshop and garage equipment, Panel capacity check | Homeowners adding a high-draw appliance that needs its own breaker and wiring run from the panel | A dedicated circuit keeps the appliance load off shared wiring and prevents nuisance tripping on other devices in the same area. |
| Breaker & Fuse Repair | Breaker that will not reset, Repeatedly tripping circuits, Fuse panel assessment, Breaker replacement | Homeowners dealing with a breaker that keeps failing under normal household load | A breaker that trips repeatedly is often a sign of an overloaded circuit or a failing breaker, not just a nuisance. We check the underlying cause before replacing hardware. |
| Wiring & Circuit Installation | Whole-home rewiring, Knob-and-tube replacement, Aluminum wiring remediation, New circuit runs | Older homes being renovated, failing inspection, or carrying wiring that was not designed for today's electrical loads | Homes built before the 1980s in the Spring area may still have knob-and-tube or aluminum branch-circuit wiring. We determine which approach fits after a diagnostic. |
| Lighting Installation | Recessed and LED retrofit, Under-cabinet lighting, Security and motion-sensor lights, Outdoor landscape wiring | Homeowners updating interior lighting or adding exterior lighting for safety and property value | Outdoor circuits require weatherproof fixtures and GFCI protection. We confirm the right protection is in place on every outdoor installation. |
| Ceiling Fan Installation | Fan mounting and wiring, Switch and remote setup, Bathroom exhaust fan wiring, Fixture replacement | Harris County homeowners where ceiling fans run most of the year and proper wiring at the box matters | Many older homes have ceiling boxes rated for a light fixture, not the weight of a fan. We confirm the box and wiring are correct before mounting. |
What are the signs that a panel or service upgrade is needed?
A buzzing or warm panel, breakers that trip under normal load, a main breaker that will not hold, or a panel that has run out of open slots are all signals worth taking seriously. Homes adding an EV charger, a generator, or a major appliance often find that the existing service cannot carry the added load without an upgrade. We run load calculations before any panel work is scheduled so the new service is sized correctly for what the home needs now and what is planned.
What causes a breaker to trip repeatedly?
A breaker that trips repeatedly is usually telling you one of three things: the circuit is carrying more load than it was designed for, a device or appliance on that circuit has a fault, or the breaker itself is failing. Resetting it without finding the cause just delays the diagnosis. We check the circuit load, the wiring, and the connected equipment before replacing any hardware, so the fix addresses what is actually wrong.
What do flickering or dimming lights usually mean?
Flickering in a single room usually points to a loose connection, a failing fixture, or a problem with the circuit feeding that area. Flickering throughout the whole house often points further back, to the panel or the service entrance. Dimming when a large appliance starts up can mean the circuit is shared and undersized for the combined load. We trace the symptom to the source before quoting any repair.
Faults Traced Before Anything Is Replaced
We locate the source of the problem before recommending a repair. That means you get a fix that addresses what is actually wrong, not a parts swap that leaves the underlying issue in place.
Why is a warm or buzzing outlet a concern?
An outlet that feels warm to the touch or makes a buzzing sound is not a minor inconvenience. Warmth at the receptacle usually means resistance in the connection, which generates heat. Buzzing can indicate a loose wire or a failing device. Both are conditions that can worsen over time. We check the outlet, the wiring behind it, and the circuit it sits on to determine what is causing the problem.
How does surge protection at the panel differ from a plug-in strip?
A plug-in surge strip handles small fluctuations at the outlet it is plugged into. It does not protect the wiring, appliances, or electronics on other circuits throughout the house. When a lightning strike or a utility surge hits the service entrance, the energy travels through the panel and out to every circuit before a strip at the outlet can do anything about it. Panel-level surge protection intercepts the surge at the point of entry. In Harris County, where summer lightning is a regular occurrence, that level of protection covers the whole home, not just what is plugged into one strip.
What are the concerns with aluminum or knob-and-tube wiring in older homes?
Knob-and-tube wiring was not designed for the electrical loads a home carries today, and it lacks a grounding conductor. Aluminum branch-circuit wiring, common in homes built in the 1960s and 1970s, expands and contracts with heat in a way that can loosen connections over time. Both types of wiring present real concerns as a home ages or as the load on the system increases. We assess the existing wiring and explain what the situation involves before recommending a repair approach or a rewire.
Scope Agreed Before the Panel Is Opened
The scope and the price are confirmed before any work begins. We explain what the job involves and what it will cost so you can make an informed decision before we pick up a tool.
How does grounding and bonding work in an older home?
Grounding gives fault current a safe path back to the source so a breaker can trip and clear the fault. Bonding ties metal components together so they stay at the same electrical potential, which is especially important around water. Older homes often have two-prong outlets with no grounding conductor, or grounding that was added later in ways that do not meet current standards. We check the grounding and bonding as part of a safety inspection and explain what needs attention and why.
What does EV charger installation involve?
A Level 2 EV charger runs on a 240-volt dedicated circuit, and the first step is confirming the panel has the capacity to support it. We check the available amperage and the existing load before running the circuit to the garage or parking area. The charger can be hardwired or outlet-mounted depending on the equipment and the setup. If the panel is at capacity, we discuss a service upgrade or load management options before the circuit is added. We scope all of that on the call so you know what the job involves before we schedule.
Older and Newer Wiring Both Handled
From knob-and-tube and aluminum branch-circuit wiring in older Spring-area homes to modern panel work and EV charger circuits, we handle the full range of what comes up in Harris County residential and commercial properties.
How long does a panel upgrade or whole-home rewire typically take?
A panel upgrade is usually a single-day job, though the timeline depends on the scope of the work, whether a subpanel is involved, and what the service entrance requires. A whole-home rewire takes longer, often several days, depending on the size of the home, how accessible the wiring runs are, and whether the walls are open or finished. We give you a realistic timeline when we scope the job, not after we start.
When is it reasonable to attempt a DIY electrical fix, and when should you call?
Swapping a light fixture for a direct replacement, changing a switch plate, or replacing a plug-in device are tasks most homeowners can handle safely. Anything that involves opening the panel, adding a circuit, replacing a breaker, or tracing a fault in the wiring is work where a mistake can create a hazard that is not obvious until something goes wrong. If you are not certain what the problem is or where it is, the call is worth making. We can often scope the situation on the phone and tell you what the job actually involves.
Is a home ready for added electrical load after a panel upgrade?
A panel upgrade increases the available capacity at the service, but whether the home is ready for a specific added load depends on the circuits feeding that load, the wiring gauge, and how the new demand fits into the overall system. We run load calculations before and after an upgrade to confirm the system can carry what is planned. Adding a generator, an EV charger, and a new HVAC circuit at the same time, for example, requires a different sizing conversation than adding a single appliance circuit.
Call (346) 654-6979 and we will go through the details, scope the job, and give you a clear price before anything is scheduled.
(346) 654-6979